Components from American and European producers, high-precision linear motors and a fast worktable interchange system provide high quality and productivity 24/7
| Working area dimensions | 1500х3000 mm |
| Average emission power | 4000-20000 W |
| Z-axis motion stroke | 100 mm |
| Maximum vector power of XY motion | 180 m/min |
- 2 years warranty
- Start-up and commissioning
- Personnel training
- Linear motor
- Ukrainian producer
- 9 levels of service
AFX-series gantry-format laser systems provide industrial processes automation with improved functionality in each subsequent model. Robotization and optimization of repetitive actions is not just a trend in the industry, but also a confident step towards improving the product quality and increasing the number of customers. High-performance solution for large and medium-sized businesses.
- AFX-Pro is an advanced model of the AFX series with a wide range of application functionality. The system is designed for cutting and high-complexity contouring, engraving, and piercing of sheet metal. The maximum vector speed has been increased to 180 m/min.
- The perfect tool for in-house serial production, the automated dual-pallet table provides the highest productivity and machining efficiency 24/7.
- The weighted welded bed dampens vibration and provides high machining dynamics with preservation of cutting precision over time. And the use of a drive on the basis of synchronous linear motors guarantees quality for at least 5-10 years.
- Hermetic cutting zone with the possibility of connecting an external exhaust provides the first protection class against laser hazard during normal operation and provides an advanced on-site safety level for the maintenance personnel and operator.
| Laser type | ytterbium fiber |
| Beam delivery | optical fiber |
| Emission/cutting modes | pulse, continuous wave |
| Laser wavelength | 1064-1070 nm |
| Safety glass replacement system | cartridge |
| Focusing system | automatic |
| Gap control system | non-contact, automatic |
| Precision of positioning in X, Y axis | ±0.01 mm |
| Positioning resolution | 1 µm |
| Cut width (depending on thickness of the material) | 0.08-0.2 mm |
| Applied process gases | oxygen, nitrogen, argon, compressed air |
| Switching of cutting gas | automatic |
| Kinematic scheme | gantry, fixed sheet |
| Drive | linear, direct |
| Motors | synchronous brushless linear motors |
| Maximum vector speed of XY movement | |
| Machining area dimensions | 1500x3000 mm |
| Table | dual-pallet automated shuttle table |
| Table replacement time | 18 sec |
| Waste removal system | trays |
| Z-axis motion stroke | 100 mm |
| Linear drive on axes | X, Y, Z |
| CNC System | ARAMIS CNC |
| Nesting of parts on a virtual table | automatic/manual |
| Data formats | DXF, DWG, G-code |
| Data loading methods | Internet, local network, USB flash drive |
| Capability to set micro-bridges within the cutting contour | + |
| "FlyCut" cutting method | + |
| Automatic tool radius compensation | + |
| Operator lockout capability | + |
| Table of processing parameters | + |
| Option to change/add processing parameters | + |
| Combined detail cutting with automatic cutting width compensation | + |
| Jump motion optimization | + |
| Obstacle avoidance function | + |
| tracking and storage of sheets, blanks, parts, and skeletons | + |
| Monitoring of processing and process parameters | + |
| Compilation of reports and operator tasks | + |
| Remote machine diagnostics | + |
| Power supply voltage | 380V, ±10%, 50Hz, 3 phases |
METALIX functions
Licensed software from Metalix is an integrated system with postprocessor that covers the complete CNC operation cycle and includes automation modules such as drawings, machining, parts nesting, postprocessor, simulation, import and export of work files.
It optimizes nesting of complex shapes. Graphical work simulation makes it easy to edit control program codes while viewing the results of processing.
The control application is automatically checked for errors.
An option is available to convert finished control program codes back into a drawing and simulate their processing.
Basic delivery set
- Motion system
- Support frame;
- X-Y axes system based on synchronuous linear motors;
- Z-axis motion drive of the cutting head;
- Schneeberger guide rails;
- Pneumatic system;
- Machine platen size 1500x3000mm;
- Cabinet-type protection (hermetic zone).
- ARAMIS CNC system;
- Technologist’s software: 1 Metalix license;
- Laser source with power supply unit;
- Optical cutting head with autofocus;
- ARAMIS Chiller system.
Extra options
- Maximum sheet dimensions1.5×3m
- Metal thickness0.5-20mm
- Maximum lift speed0.4 m/sec
- Maximum sheet dimensions1.5×3m
- Metal thickness0.5-20mm
- Maximum lift speed0.4 m/sec
- Maximum sheet dimensions1.5×3m
- Metal thickness0.5-12mm
- Maximum lift speed0.4 m/sec
- Maximum sheet dimensions1.5×3m
- Metal thickness0.5-12mm
- Maximum lift speed0.4 m/sec
- Maximum sheet dimensions1.5×3m
- Metal thickness0.5 -20mm
- Maximum lift speed0.4 m/sec
- Maximum sheet dimensions1.5×3m
- Metal thickness0.5 -20mm
- Maximum lift speed0.4 m/sec
Max thickness of the material to be cut
Materials: Н – stainless steel; А – Aluminum; Ч – carbon steel.
*Color intensity corresponds to speed and quality of the cut.
| Thickness, mm | Material | Speed (m/min) | Gas | |||||||
|---|---|---|---|---|---|---|---|---|---|---|
| IPG 1,5KW | IPG 2KW | IPG 3KW | IPG 4KW | IPG 6KW | IPG 12KW | IPG 15KW | IPG 20KW | |||
| 1 | Structural steel | 9 | 9 | 9 | 10 | 10 | 11 | 11 | 11 | О2 |
| 2 | 5,6 | 5,7 | 6 | 6 | 6 | 6,5 | 6,5 | 6,5 | ||
| 3 | 3,2 | 3,5 | 3,7 | 3,8 | 3,8 | 4,2 | 4,2 | 4,2 | ||
| 4 | 3 | 3 | 3,3 | 3,4 | 3,4 | 3,8 | 3,8 | 3,8 | ||
| 5 | 2,5 | 2,8 | 3 | 3,2 | 3,2 | 3,7 | 3,7 | 3,7 | ||
| 6 | 2,3 | 2,5 | 2,7 | 2,8 | 2,8 | 3,3 | 3,3 | 3,3 | ||
| 8 | 1,4 | 1,6 | 1,8 | 2,5 | 2,5 | 2,7 | 2,7 | 2,7 | ||
| 10 | 1,2 | 1,2 | 1,3 | 1,4 | 2,1 | 2,3 | 2,3 | 2,3 | ||
| 12 | 1 | 1 | 1 | 1 | 1,4 | 2 | 2 | 2 | ||
| 14 | 0,8 | 0,8 | 0,8 | 0,8 | 1,8 | 1,8 | 1,8 | |||
| 16 | 0,7 | 0,8 | 0,8 | 1,6 | 1,6 | 1,6 | ||||
| 18 | 0,7 | 0,7 | 0,7 | 1,4 | 1,4 | 1,4 | ||||
| 20 | 0,6 | 0,6 | 1,2 | 1,2 | 1,4 | |||||
| 25 | 0,7 | 1 | 1,2 | |||||||
| 30 | 0,7 | 1 | ||||||||
| Thickness, mm | Material | Speed (m/min) | Gas | |||||||
|---|---|---|---|---|---|---|---|---|---|---|
| IPG 1,5KW | IPG 2KW | IPG 3KW | IPG 4KW | IPG 6KW | IPG 12KW | IPG 15KW | IPG 20KW | |||
| 1 | Stainless steel | 25 | 30 | 35 | 35 | 40 | 50 | 50 | 50 | N2 |
| 2 | 10 | 12 | 20 | 20 | 30 | 35 | 35 | 45 | ||
| 3 | 4,5 | 6 | 8 | 9 | 15 | 25 | 25 | 40 | ||
| 4 | 2,6 | 3,2 | 4,5 | 5,5 | 12 | 20 | 22 | 30 | ||
| 5 | 1,6 | 1,8 | 3 | 4,5 | 7,8 | 13 | 16 | 22 | ||
| 6 | 0,9 | 1 | 2 | 3,2 | 6 | 10 | 12 | 18 | ||
| 8 | 0,6 | 1,2 | 1,9 | 3,5 | 7 | 8 | 12 | |||
| 10 | 0,8 | 1,3 | 2,1 | 5 | 6 | 10 | ||||
| 12 | 0,8 | 1,5 | 4 | 5 | 8 | |||||
| 14 | 1 | 3 | 4 | 6 | ||||||
| 16 | 0,8 | 2 | 2,6 | 5 | ||||||
| 18 | 0,5 | 1,4 | 2 | 3,2 | ||||||
| 20 | 1 | 1,6 | 3 | |||||||
| 25 | 0,6 | 1 | 1,5 | |||||||
| 30 | 0,6 | 1 | ||||||||
| Thickness, mm | Material | Speed (m/min) | Gas | |||
|---|---|---|---|---|---|---|
| IPG 3KW | IPG 4KW | IPG 6KW | IPG 8KW | |||
| 1 | Aluminum | 40 | 40 | 50 | 60 | Air |
| 2 | 20 | 20 | 30 | 35 | ||
| 3 | 8 | 8,2 | 12 | 20 | ||
| 4 | 4 | 5,5 | 10 | 15 | ||
| 5 | 2,8 | 3,8 | 8 | 12 | ||
| 6 | 1,8 | 2,4 | 5,5 | 10 | ||
| 8 | 1,1 | 1,2 | 3 | 5 | ||
| 10 | 0,9 | 0,9 | 1,5 | 2 | ||
| 12 | 0,7 | 1 | 1 | |||
| 14 | 0,5 | 0,8 | 0,8 | |||
- Requirements to the premises for placement of technological equipment
- For placement of the machine there is no need for a special basement. The level difference of the floor surface (height discontinuity) in the horizontal plane over a length of 2 meters should may not exceed 4 mm (according to SNiP Construction Standards and Rules 2.03.13-88 “Floors”) under the area for the laser system placement;
- Size of the concrete pad should be at least the total area of the entire system, including additional equipment, with a depth of no less than 140 mm;
- The floor and walls of the room should not be a source of dust (especially cement plaster dust);
- Width of all passages between elements of the equipment or between the equipment and walls of the room (workshop) should be no less than 0.5 meters, and, in some cases, no less than 1 meter;
- Power supply specifications
- The system shall be plugged to 5-wire 3 phase industrial power grid 380-?-400 W with acceptable deviation +-10%; 50+-1Hz frequency with acceptable electric power consumption in accordance with the system’s needs. Interphase balance may not exceed +2%. Electric power quality standards in accordance with State Standard GOST ГОСТ 13109-97;
- The system shall be equipped with a three-phase voltage stabilizer to stabilize the voltage against possible swings in the network, which in turn will ensure uninterrupted and reliable operation of the machine;
- The system must be earthed. That is, connect the earthing circuit of the machine with a cable to the earthing bolt. The cable cross-section must be at least 4 sq. mm.
- Operating microclimate conditions:
Prepare the premises to maintain a stable temperature to ensure operation within the range of +10 to +32 C and relative humidity of 80% (at the temperature of 20 C) without condensate formation, at the atmospheric pressure of 83.9-106.6 kPa (630-800 mm Hg);
Make sure there are no active substances in the room where the system is placed;
Temperature fluctuations during operation shall not exceed the limit of +3C
- Requirements to the air extraction system:
The premises shall be equipped with exhaust ventilation to remove combustion products and process-generated dust with the total pressure of no less than 1950 Pa and the productivity of no less than 4250 m3/h.
The system must be connected to the aforesaid exhaust ventilation system with a 315 mm diameter ventilation hose or pipe.
- Supply of Process gas (for the cutting process):
For laser cutting, the following should be used: oxygen in cylinders (99.7% purity), nitrogen (99.97% purity) or an industrial network of dried compressed air must be available (water content not exceeding 0.005%, oil content not exceeding 0.002%, no worse than the 4th containment class according to state standard GOST 17433-80, pressure no less than 14 bar);
Requirements to the operation and storage of cylinders should be based on safety regulations for handling of flammable (oxygen) and non-flammable (nitrogen, argon) gases, which are valid in the country where the system is to be used.
- Utility air supply (for pneumatic equipment operation):
Supply of purified, dehumidified compressed air to the auxiliary pneumatic units of the laser system: by a pneumatic pipe with an internal and external diameter of 10 mm and 12 mm, respectively. Air purification in accordance with DIN ISO 8573-1: oils no more than 0.002%, water no more than 0.005%, particle size up to 40 microns, not worse than class 4 contamination in accordance with state standard DEST ДЕСТ 17433-80, pressure 6…8 bar, maximum losses: 0.5 l/min.
- Requirements to the cooled liquid of the machine’s cooling system:
Cooling liquid: distilled water;
The quality of distilled water in the cooling system (chiller) circuit shall comply with ISO 22519:2019 (recommended water quality – after reverse osmosis) with hardness of no more than 0.25 dH ) = 4.45 ppm = 0.089 ml/liter and electrical conductivity of no more than 50 μS/cm
A brief overview of the advantages
you get when using our machines
Watch the machines in operation
on the production site
at exhibitions
in the workshop
9 levels of service provided by ARAMIS
We are trusted by over 250 manufacturers
- Industry
- Location
Amidst the advantages of cooperation with ARAMIS company we would like to mention qualified technical and service support of the equipment, which allows to operate the laser machine without downtime and, as a consequence, not to suspend the production cycle of our company.
We are confident in the established business and friendly relations and recommend LLC ARAMIS as a reliable and responsible domestic producer of laser equipment.
During the operation of the metal laser cutting machine, ARAMIS LLC has demonstrated a high level of technical and service support for its products throughout the entire usage period, which is essential for us as a customer.
Overall, based on our experience with the machine, we are satisfied with the performance of the LTC75-2000-3015 LD model, both in terms of its manufacturing quality and productivity. We wish your company prosperity and look forward to continued constructive cooperation.
Samples of work
Customers who have viewed this product are also interested in
- Dimensions of the machining area1.5х3m
- Average laser beam power1.5-6 kW
- Maximum XY motion vector speed120 m/min
- Dimensions of the machining area1.5х3m
- Average laser beam power1.5-6 kW
- Maximum XY motion vector speed120 m/min
- Dimensions of the working area2х6m
- Average laser beam power2-6 kW
- Maximum vector speed of XY motion120 m/min
- Dimensions of the working area2х6m
- Average laser beam power2-6 kW
- Maximum vector speed of XY motion120 m/min
- Dimensions of the working area1.5×3m
- Average laser beam power2-6 kW
- Maximum vector speed of XY motion150 m/min
- Dimensions of the working area1.5×3m
- Average laser beam power2-6 kW
- Maximum vector speed of XY motion150 m/min
- Dimensions of the working area1.5×3m
- Average emission power4-20 kW
- Maximum vector speed of XY motion240 m/min
- Dimensions of the working area1.5×3m
- Average emission power4-20 kW
- Maximum vector speed of XY motion240 m/min
- Laser sourceRaycus
- Laser source power20, 30, 50 W
- Engraving area100х100; 200х200 mm
- Laser sourceRaycus
- Laser source power20, 30, 50 W
- Engraving area100х100; 200х200 mm
- Dimensions of the working area2×4; 2x6m
- Average laser beam power4-20 kW
- Maximum vector speed of XY motion150 m/min
- Dimensions of the working area2×4; 2x6m
- Average laser beam power4-20 kW
- Maximum vector speed of XY motion150 m/min
- Maximum sheet dimensions1.5×3m
- Metal thickness0.5-12mm
- Maximum lift speed0.4 m/sec
- Maximum sheet dimensions1.5×3m
- Metal thickness0.5-12mm
- Maximum lift speed0.4 m/sec
These subjects can be of interest for you
In case of industrial equipment, the decision to purchase used equipment requires careful consideration. This is especially true for used laser cutting machines, a technological asset that can be a blessing or a curse depending on the specific circumstances.
Advantages of ordering metal cutting services Provision of metal cutting services by a professional contractor can provide many advantages for the business. Here are some of the main ones: 1. Cost effectiveness: Outsourcing can be more cost-effective than purchasing of in-house equipment, especially for companies with small production volumes. It eliminates the need for expensive […]
How to choose a laser machine for metal cutting? Owners of industrial enterprises for the manufacture of metal products are paying increasingly careful attention to laser machines for metal cutting, which feature versatility, reliability and high precision. That goes without saying: when purchasing such equipment, the question arises quite naturally – what characteristics of the […]
What is laser cutting of metals? Metal laser cutting is a process where a laser beam is applied to cut metal parts to a specific size and shape. This method of metal processing is the most precise and efficient compared to other cutting methods, such as plasma cutting or gas cutting.
Power of the supplied laser sources
Laser cutting machine | Laser power, W | Maximum sheet thickness (Steel3) |
AFX-PRO-2000 | 2000 | Up to 14.0 |
AFX-PRO-3000 | 3000 | Up to 18.0 |
AFX-PRO-4000 | 4000 | Up to 20.0 |
AFX-PRO-6000 | 6000 | Up to 25.0 |
AFX-PRO-12000 | 12000 | Up to 30.0 |